Articles

Access the latest knowledge in applied science, electrical engineering, computer science and information technology, education, and health.

Advanced Search
Filter Icon

Filters article

Years

FAQ Arrow
Single Year
Range Year
0
0

Source Title

FAQ Arrow

Authors

FAQ Arrow

31,456 Article Results

An analytical technique for failure analysis and reliability assessment of grid daily outage performance in distributed power system

10.11591/ijpeds.v16.i3.pp1852-1864
Jacob Kehinde Ogunjuyigbe , Evans Chinemezu Ashigwuike , Kafayat Adeyemi , Ngang Bassey Ngang , Timothy Oluwaseun Araoye , Isaac Ojochogwu Onuh , Benson Stephen Adole , Solomon Bala Okoh , Iboi Endurance
This paper modeled and analyzed the reliability performance of the 132/33 kV substation in Abuja, Nigeria through the historical data collected from the APO substation using MATLAB 2021b. The probability distribution model was applied to determine the daily feeder’s outage using Reliability, availability, mean time to repair (MTR), Failure rate, distribution indices, and mean time between failures (MTBF). Due to the application of smart energy meters, the use of prepaid energy meters has helped to regulate energy demand, reduce network overloading especially during peak hours, and minimize the cost of energy consumed. There are more forced failures in the distribution system due to the switchgear and Transformer failures. There are more forced failures in the distribution system since 2013, which caused a reduction in the number of interruptions even with an increase in several customers linked to the transmission network. The result shows that the system was most available in the year 2015 with an average service availability index (ASAI) value of 98.9971%. The system was least available in year 2011 with an ASAI value of 98.6558%. The paper recommended that there should be interconnections between different feeders through proper configuration of switches or reclosers, to reduce failure occurrence in the network.
Volume: 16
Issue: 3
Page: 1852-1864
Publish at: 2025-09-01

Enhancement of power quality of grid integrated photo voltaic system using active power filter

10.11591/ijpeds.v16.i3.pp2017-2029
Praveen Kamat , Anant Naik
The world's population's energy needs are growing daily, while at the same time, fossil fuels are being reduced at an alarming rate. Fossil fuel burning also increases pollution and causes global warming. Renewable energies are now being extensively used to generate electricity, so the dependence on fossil fuels is considerably reduced. Among the primary sources of alternative energy used to create power is photovoltaic (PV) technology. A grid connected PV system is the most widely recommended. When PV is linked to the grid, two main issues are the maximum power that can be taken out of it and the quality of the electricity placed into it. With the help of neural networks, the maximum power point tracking (MPPT) technology has been developed to increase the PV array's power harvesting. An active power filter (APF) had been created and analyzed using Instantaneous Reactive Power Theory, including the Chebyshev II low-pass filter. As required by IEEE 519, the total harmonic distortion (THD) with injected source current has been confirmed well within 5%. These results demonstrate that this method is a simple and efficient way to inject harmonic-free currents into the grid.
Volume: 16
Issue: 3
Page: 2017-2029
Publish at: 2025-09-01

Photovoltaic energy harvesting for the power supply of medical devices

10.11591/ijpeds.v16.i3.pp1962-1969
Hamza Abu Owida , Basem Abu Izneid , Nidal Turab
The increasing demand for sustainable and reliable power sources in portable and implantable medical devices has led to growing interest in photovoltaic (PV) energy harvesting. Traditional power sources, such as batteries, are limited by finite energy capacity and frequent replacement or recharging needs, particularly in implantable devices where surgical intervention is required for battery replacement. Photovoltaic energy harvesting, which converts light into electrical energy, offers a promising alternative, especially in environments with consistent light exposure. This review provides an in-depth analysis of the advancements in PV technologies for powering medical devices. It covers various types of PV materials, design innovations, and the integration of energy storage systems. Additionally, the review highlights the application of PV systems in both external and implantable medical devices, while addressing critical challenges such as ensuring biocompatibility, optimizing performance in low-light conditions, and miniaturizing PV systems for implantation. The potential of PV energy harvesting to improve device longevity and reduce the need for invasive procedures is emphasized. This review concludes by outlining the current challenges and future directions needed to achieve widespread clinical adoption, aiming to contribute to the development of sustainable power solutions in healthcare.
Volume: 16
Issue: 3
Page: 1962-1969
Publish at: 2025-09-01

Islanding detection of integrated DG system using rate of change of frequency over reactive power

10.11591/ijpeds.v16.i3.pp1637-1644
B. V. Seshu Kumari , Ambati Giri Prasad , S. Sai Srilakshmi , Karri Sairamakrishna Buchireddy , Ch. Rami Reddy
This paper offers a passive islanding detection method that is effective for distributed generation. When a distributed generator (DG) keeps a location powered even when access to the external electrical grid is lost, this circumstance is referred to as islanding. The power distribution system currently includes distributed generators (DGs), which provide inexpensive electricity and have fewer environmental impacts. Sometimes, these DGs continue to supply the nearby loads because of line outages and islands made by system separations. As a result, there are scenarios with unacceptable power quality. The islanding is identified if the result of the rate of change of frequency over reactive power exceeds the threshold value. The MATLAB test results from this study demonstrate the effectiveness of the suggested approach for different islanding and non-islanding scenarios.
Volume: 16
Issue: 3
Page: 1637-1644
Publish at: 2025-09-01

Solar cell-based garden light automation for environmentally friendly technology learning

10.11591/ijpeds.v16.i3.pp1457-1471
Afrizal Mayub , Fahmizal Fahmizal , Lazfihma Lazfihma
This research aims to: 1) Produce a prototype design for a solar cell-based automatic garden lighting system; 2) Determine the relationship between current, power, and voltage and light intensity; 3) Describe the feasibility of an environmentally friendly technology practicum guidebook; and 4) Describe teacher and student responses to the environmentally friendly technology practice guidebook. This research is R&D type Analysis, Design, Development, Implementation and Evaluation (ADDIE) Analysis, design, development, implementation and evaluation. The research sample used 44 class IX students at MTS Rahmatullah. According to students, aspects of teaching materials, aspects of content, and difficulty of teaching materials at school are inadequate at 84.25%, 80% and 82.5%. Student interest in environmentally friendly technology practicum guidebooks was 84.25%. The higher the light intensity, the higher the current, power, and voltage. Expert validation shows; the prototype of an automatic garden lighting system based on solar cells and a practical guidebook on environmentally friendly technology are very suitable for use (89.14% and 90.75%). The use of environmentally friendly technology practicum guidebooks increased students' critical thinking skills in the high category (N-Gain = 0.7937) and received responses from teachers and students in the "almost all" category (91.50% and 89.9%).
Volume: 16
Issue: 3
Page: 1457-1471
Publish at: 2025-09-01

Oxygen/sulphur self-doped tunnel-like porous carbon from yellow bamboo for advanced supercapacitor applications

10.11591/ijpeds.v16.i3.pp2030-2042
Erman Taer , Novi Yanti , Rahma Lia Putri , Apriwandi Apriwandi , Awaludin Martin , Julnaidi Julnaidi , Nidya Chitraningrum , Ahmad Fudholi , Rika Taslim
The 3D hierarchical pore structure with tunnel-like pores is essential to the performance of porous activated carbon (AC) materials used in symmetric supercapacitors. This study aimed to effect of adding (0.3, 0.5, and 0.7) M KOH reagent and heat treatment on the formation of 3D porous, tunnel-like AC derived from yellow bamboo (YB) through N2-CO2 pyrolysis at 850 °C. The AC produced had a high concentration of nanopores, becoming a valuable storage medium with favorable physical-electrochemical properties. The results showed that 0.5-YBAC had the best physical and electrochemical properties, with a carbon purity, 89.16%, micro crystallinity of 7.374 Å, and excellent amorphous porosity. Furthermore, 3D hierarchical pore structure, enriched naturally occurring heteroatoms, dopant of oxygen (10.14%) and sulfur (0.10%). A maximum surface area of 421.99 m² g⁻¹, along with a dominant combination of micro-mesopores. The electrochemical performance test of the 0.5-YBAC electrode showed a Csp of 214 F g⁻¹, with Esp 24.7 Wh kg⁻¹ and Psp 19.2 W kg⁻¹. In conclusion, this study showed the potential of YB stems to enhance the development of supercapacitors, offering superior porosity characteristics for efficient energy storage applications.
Volume: 16
Issue: 3
Page: 2030-2042
Publish at: 2025-09-01

Bibliometric visualization of metal-air battery research trends

10.11591/ijpeds.v16.i3.pp1865-1880
Satria Pinandita , Rustam Asnawi , Mochamad Syamsiro
Metal-air batteries are rechargeable secondary batteries with high energy density, typically using carbon electrodes. However, carbon waste poses environmental risks. Fly ash, a byproduct of coal combustion, offers a sustainable alternative due to its high electrical conductivity. This study analyzes research trends on metal-air batteries and fly ash from 2019 to 2023 using bibliometric visualization of Scopus-indexed publications. The keyword search was refined from 'Battery' to 'Air Battery' and, finally, 'Air Battery' with 'Fly Ash,' yielding 60 relevant articles. Using the VOSviewer, research patterns, key focus areas, and collaboration networks were identified. The results indicate a 14.87% increase in publications from 2019 to 2023, with significant growth from 2019 to 2021 before declining after 2022. This fluctuation suggests shift in research interests toward other battery technologies. Fly ash demonstrates potential as a carbon substitute for air batteries, promoting sustainability. However, further research is needed to optimize its application and address technical challenges. Bibliometric visualization highlights a growing interest in fly ash for environmentally friendly battery development due to its abundance and sustainability.
Volume: 16
Issue: 3
Page: 1865-1880
Publish at: 2025-09-01

When studying applied physics: what problems are there, and do pre-service physics teachers need?

10.11591/ijaas.v14.i3.pp650-661
Renol Afrizon , Lilia Ellany Mohtar , Mohd Syahriman Mohd Azmi , Hidayati Hidayati
Applied physics courses are essential for pre-service physics teachers (PsPTs), but they often encounter challenges in pursuing this educational pathway. This study aims to identify the problems and learning elements that PsPTs need in applied physics learning using the McKillip discrepancy model. The data were collected using questionnaires and bibliometric techniques. A total of 23 PsPTs participated in the study. Additionally, 1,000 articles were consulted as a data source. The data analysis uses descriptive statistics and the VOSviewer software. The first finding is primary issues identified in applied physics learning e.g., the difficulty of locating suitable learning resources, the dearth of in-depth physics comprehension, the absence of visualization like augmented reality (AR), the failure to undertake empirical activities in the laboratory, and global warming and climate change topic were pertinent at the high school level, entailed intricate issues, and were abstract. The second finding is a learning module that is integrated with science, technology, engineering, and mathematics (STEM), and AR is needed by PsPTs. Finally, this need has been paramount over the past decade to meet PsPTs' needs. Thus, the needs analysis results serve as an initial reference point for decision-makers to identify elements and develop integrated STEM and AR applied physics learning modules.
Volume: 14
Issue: 3
Page: 650-661
Publish at: 2025-09-01

Deep learning for image classification of submersible pump impeller

10.11591/ijaas.v14.i3.pp838-848
Phan Nguyen Ky Phuc , Doan Huu Chanh , Trong Hieu Luu
This study presented a deep learning-based model in the submersible pump impellers quality inspection process. The proposed method aimed to relieve worker workload, automate the system, as well as increase the accuracy in defect detection and classification. The proposed approach aims to be implemented on systems with low investment cost and limited resources, i.e., small single-board computers, enabling flexible deployment in industrial environments. The model consisted of three convolutional neural network (CNN) models, i.e., visual geometry group 16 (VGG16), ResNet50, and a custom model. The outputs of three networks were either synthesized later through an ensemble stage or used separately. A graphical user interface (GUI) was also developed for real-time inspection and user-friendly interaction. The approach achieved up to 99.8% accuracy in identifying defects, including surface scratches, corrosion, and geometric irregularities. The proposed method improved the quality assurance process by reducing manual inspection efforts. Future research could explore advanced techniques like anomaly detection to further enhance system performance and versatility.
Volume: 14
Issue: 3
Page: 838-848
Publish at: 2025-09-01

Structural behavior of reinforced soil walls under seismic loads

10.11591/ijaas.v14.i3.pp711-723
Reynaldo Melquiades Reyes Roque , Lincoln Jimmy Fernández Menacho , Brayanm Reynaldo Reyes Huerta , Fabrizio del Carpio Delgado
One of the main engineering challenges has been to design an economical soil retaining structure with high seismic resistance. From this perspective, reinforced soil walls have been developed with a focus on flexibility, in order to efficiently resist the effects of similar historical events in the event of a significant earthquake. The overall objective of this study was to compare the structural behavior of a geogrid-reinforced soil wall (Terramesh® system) under static and pseudo-static loads, and in a seismic environment simulated using the finite element method, in a shopping center in Trujillo, Peru. A case study was conducted using a mixed methodology, both applied and analytical-comparative in scope. Furthermore, the finite element methodology, material constitutive modeling, and dynamic time-history analysis of modal structures were chosen. It was determined that seismic loading can produce a 53.33% increase in deformations compared to the static state; Likewise, the overall safety factor under dynamic conditions tends to decrease by 27.85% compared to the static case. This study demonstrated the scope of geogrid reinforcement (Terramesh® system) through a practical case of a reinforced soil wall, using Plaxis 2D software to compare, estimate, and compare structural behavior in static, dynamic, and simulated environments.
Volume: 14
Issue: 3
Page: 711-723
Publish at: 2025-09-01

Wireless charging Class-E inverter for zero-voltage switching over coupling coefficient range

10.11591/ijpeds.v16.i3.pp1752-1764
Anon Namin , Chuchat Donloei , Ekkachai Chaidee
A novel and practical methodology is presented in this study for designing contactless wireless energy systems using resonant-mode Class-E converters, aiming to sustain efficient soft-transition switching under various levels of magnetic coupling, even under coil misalignment. The approach integrates the wireless power transfer (WPT) circuit with the inverter’s series resonant network and analytically derives the relationship between the coupling coefficient and impedance phase angle to identify zero voltage switching (ZVS) conditions. A key contribution is the use of the maximum expected coupling coefficient as a critical design point to ensure ZVS across practical variations. A complete step-by-step design procedure is provided. Simulation and experimental results confirm that the inverter achieves and maintains ZVS for coupling values in the range 0 < k ≤ kdesigned, with efficiencies reaching up to 95%. This work supports the advancement of soft-switching inverter design to enable robust and efficient WPT systems under practical misalignment conditions.
Volume: 16
Issue: 3
Page: 1752-1764
Publish at: 2025-09-01

Low voltage fault ride-through operation of a photo-voltaic system connected utility grid by using dynamic voltage support scheme

10.11591/ijpeds.v16.i3.pp1608-1619
Satyanarayana Burada , Kottala Padma
This research suggests a control technique that makes use of a microgrid's energy storage and to enable low voltage ride through (LVRT) process with a flexible dynamic voltage support (DVS) system. First, the requirements for the microgrid's maximum DVS are stated, together with an explanation of how these requirements depend on the characteristics of the analogous network that the microgrid sees. In order to create a flexible DVS regardless of the changing system circumstances, reference signals for currents that are derived from maximum voltage tracking technique are suggested in this research. These signals take into account the challenges involved with real time parameter assessment in the context of transient voltage disruptions. Second, a control scheme is suggested to allow a microgrid's energy storage-based LVRT operation. Thirdly, a novel approach to energy storage sizing for LVRT operation is offered, taking into account the corresponding network characteristics, grid code requirements, and the rated current value of the power electronic converter. Real-time MATLAB simulations for low-voltage symmetrical faults are used to validate the suggested control technique.
Volume: 16
Issue: 3
Page: 1608-1619
Publish at: 2025-09-01

Eco-friendly durable asphalt using maleic-modified rosin ester

10.11591/ijaas.v14.i3.pp793-803
Emma Savitri , Edy Purwanto , Restu Kartiko Wisi , Aloisiyus Yuli Widianto , Reyhan Sava Pratama , Yosafat Gary Tegar Harijono
Asphalt, a crucial component of transportation infrastructure, particularly in regions with high traffic loads and extreme climates, often lacks the necessary elasticity, strength, and durability. Various asphalt modifiers have been explored, but many struggle with cost, thermal stability, and environmental impact. This study, however, investigates maleic-modified rosin ester, a gum rosin derivative, as a sustainable and cost-effective asphalt modifier. The base asphalt was heated to 150-190 °C, sheared at 100 rpm, and combined with 4-20% maleic rosin ester and sulfur. The modified asphalt was subjected to tests, including penetration, softening point, ductility, density, kinematic viscosity, Fourier transform infrared (FTIR), and dynamic shear rheometer (DSR) tests. The results are promising, showing that maleic rosin ester enhances penetration resistance and softening points while maintaining ductility and viscosity within acceptable limits. Chemical analysis confirmed improved adhesion, crosslinking, and thermal stability, making the modified asphalt more deformation-resistant. This suggests that maleic-modified rosin ester is a viable alternative to synthetic polymers, offering improved durability and sustainability. The enhanced durability of the modified asphalt provides confidence in its long-term performance, making it a reliable choice for transportation infrastructure.
Volume: 14
Issue: 3
Page: 793-803
Publish at: 2025-09-01

Dissolved organic matter released from paper trash in water during ultraviolet irradiation: impacts on trihalomethane formation

10.11591/ijaas.v14.i3.pp869-877
Teguh Budi Prijanto , Nia Yuniarti Hasan , Kahar Kahar , Muammar Qadafi , Wisnu Prayogo
When exposed to ultraviolet (UV) light, paper trash could release dissolved organic matter (DOM) as a disinfection byproduct (DBP) precursor in water. This study was undertaken to assess the regulated DBPs, trihalomethanes-4 (THM4) generation potential, and estimated cytotoxicity of paper trash soaked in water during UV radiation. The UV irradiation was carried out at 1, 6, 12, 24, and 48 hours. The released organic material was determined using ultraviolet-visible (UV-Vis) adsorption at wavelengths ranging from 200 to 700 nm. Chlorination was carried out for 24 hours to determine THM4 formation potentials. According to the research findings, the longer the radiation period, the more THM4 species are formed in plain paper samples. On the other hand, the production of trichloromethane (TCM) on paper samples containing writing decreased as the UV radiation period increased. THM4 levels reached 103.12 and 150.57 µg/L for plain and writing paper samples, respectively. UV absorbance at 272 nm (A272) shows a 92% association with THM4 production, making it suitable as an initial characterization approach. Paper trash pollution in water could form carcinogenic DBPs, THM4, if used as a water source in a water treatment plant using chlorine disinfection.
Volume: 14
Issue: 3
Page: 869-877
Publish at: 2025-09-01

A hybrid features based malevolent domain detection in cyberspace using machine learning

10.11591/ijaas.v14.i3.pp916-927
Saleem Raja Abdul Samad , Pradeepa Ganesan , Amna Salim Rashid Al-Kaabi , Justin Rajasekaran , Murugan Singaravelan , Peerbasha Shebbeer Basha
The rise of social media has changed modern communication, placing information at our fingertips. While these developments have made our lives easier, they have also increased cybercrime. Cyberspace has become a refuge for modern cybercriminals to conduct destructive actions. Most cyberattacks are carried out through malicious links shared on social media platforms, emails, or messaging services. These attacks can have serious consequences for individuals and organizations, including financial losses, sensitive data breaches, and damage to reputation. Early identification and blocking of such links are crucial to protecting internet users and securing cyberspace. Current research uses machine learning (ML) algorithms to detect malicious hyperlinks based on observed patterns in uniform resource locators (URLs) or web content. However, cyberattack tactics are constantly changing. To address this challenge, this paper introduces a robust method that performs a fine-grained analysis of URLs for classification. Lexical and n-gram features are examined separately, with URL n-grams represented using Word2Vec embeddings. The results from hybrid feature sets are combined using a logistic regression (LR) model to increase overall classification accuracy. This robust method allows the system to use both the structural components of the URL and the fine-grained patterns obtained by the n-grams.
Volume: 14
Issue: 3
Page: 916-927
Publish at: 2025-09-01
1 2 3
...
2097 2098
Show 225 of 2098

Discover Our Library

Embark on a journey through our expansive collection of articles and let curiosity lead your path to innovation.

Explore Now
Library 3D Ilustration